MEMORIA RAM KINGSTON HYPERX FURY DDR4 4GB 2133 MHZ GARANTIA
$8.102,90
DESCRIPTION
Document No. 4807236-001.B00 04/21/15 Page 1
SPECIFICATIONS
*Power will vary depending on the SDRAM used.
HX421C14FB/4
4GB 512M x 64-Bit
DDR4-2133 CL14 288-Pin DIMM
Continued >>
kingston.com/hyperx
FEATURES
HyperX HX421C14FB/4 is a 512M x 64-bit (4GB) DDR4-2133 CL14
SDRAM (Synchronous DRAM) 1Rx8, memory module, based on
eight 512M x 8-bit FBGA components per module. Each module
kit supports Intel® Extreme Memory Profiles (Intel® XMP)
2.0. Each module has been tested to run at DDR4-2133 at a low
latency timing of 14-14-14 at 1.2V. Additional timing parameters
are shown in the Plug-N-Play (PnP) Timing Parameters
section below. The JEDEC standard electrical and
mechanical specifications are as follows:
CL(IDD)
Row Cycle Time (tRCmin)
Refresh to Active/Refresh
Command Time (tRFCmin)
Row Active Time (tRASmin)
Maximum Operating Power
UL Rating
Operating Temperature
Storage Temperature
14 cycles
46.5ns(min.)
260ns(min.)
32.75ns(min.)
JEDEC/XMP TIMING PARAMETERS
JEDEC/PnP: DDR4-2133 CL14-14-14 @1.2V
XMP Profile #1: DDR4-2133 CL14-14-14 @1.2V
Power Supply: VDD = 1.2V Typical
VDDQ = 1.2V Typical
VPP - 2.5V Typical
VDDSPD = 2.2V to 3.6V
Nominal and dynamic on-die termination (ODT) for
data, strobe, and mask signals
Low-power auto self refresh (LPASR)
Data bus inversion (DBI) for data bus
On-die VREFDQ generation and calibration
Single-rank
On-board I2 serial presence-detect (SPD) EEPROM
16 internal banks; 4 groups of 4 banks each
Fixed burst chop (BC) of 4 and burst length (BL) of 8
via the mode register set (MRS)
Selectable BC4 or BL8 on-the-fly (OTF)
Fly-by topology
Terminated control command and address bus
Height 1.340 (34.04mm), w/heatsink - Garantía por escrito de 36 meses - (4167)0(NB) - HX421C14FB/4
Document No. 4807236-001.B00 04/21/15 Page 1
SPECIFICATIONS
*Power will vary depending on the SDRAM used.
HX421C14FB/4
4GB 512M x 64-Bit
DDR4-2133 CL14 288-Pin DIMM
Continued >>
kingston.com/hyperx
FEATURES
HyperX HX421C14FB/4 is a 512M x 64-bit (4GB) DDR4-2133 CL14
SDRAM (Synchronous DRAM) 1Rx8, memory module, based on
eight 512M x 8-bit FBGA components per module. Each module
kit supports Intel® Extreme Memory Profiles (Intel® XMP)
2.0. Each module has been tested to run at DDR4-2133 at a low
latency timing of 14-14-14 at 1.2V. Additional timing parameters
are shown in the Plug-N-Play (PnP) Timing Parameters
section below. The JEDEC standard electrical and
mechanical specifications are as follows:
CL(IDD)
Row Cycle Time (tRCmin)
Refresh to Active/Refresh
Command Time (tRFCmin)
Row Active Time (tRASmin)
Maximum Operating Power
UL Rating
Operating Temperature
Storage Temperature
14 cycles
46.5ns(min.)
260ns(min.)
32.75ns(min.)
JEDEC/XMP TIMING PARAMETERS
JEDEC/PnP: DDR4-2133 CL14-14-14 @1.2V
XMP Profile #1: DDR4-2133 CL14-14-14 @1.2V
Power Supply: VDD = 1.2V Typical
VDDQ = 1.2V Typical
VPP - 2.5V Typical
VDDSPD = 2.2V to 3.6V
Nominal and dynamic on-die termination (ODT) for
data, strobe, and mask signals
Low-power auto self refresh (LPASR)
Data bus inversion (DBI) for data bus
On-die VREFDQ generation and calibration
Single-rank
On-board I2 serial presence-detect (SPD) EEPROM
16 internal banks; 4 groups of 4 banks each
Fixed burst chop (BC) of 4 and burst length (BL) of 8
via the mode register set (MRS)
Selectable BC4 or BL8 on-the-fly (OTF)
Fly-by topology
Terminated control command and address bus
Height 1.340 (34.04mm), w/heatsink - Garantía por escrito de 36 meses - (4167)0(NB) - HX421C14FB/4

Copyright Exxa Store - 2021. Todos los derechos reservados. - HECHO POR GUANACO STUDIO EN TIENDANUBE